• Kılıçoğlu Banner
  • K-1
    Home / Products / K-1

    K-1

    CLAY ROOF TILES

    The first classic roof tile of Turkey...

    When it comes to tile, it is the first tile that comes to mind. Its easy application and its ability to cover roofs smoothly made Kılıçoğlu-1 tile the most preferred tile for years. It is one of its most important features that it proves itself by protecting the roofs for years against harsh weather conditions in cold climates. Offering high strength and smooth surface with Micro clay Technology, Kılıçoğlu 1 safely protects any length of roof against water leakage in case of staggered installation.

    Technical Features

    Dimensions (cm) 24x41cm (±%2)
    Dimensions (inch) 9.44x16.14 inch (±%2)
    Weight 2950gr (±100gr)
    Use 15 pcs/m²
    Endurance 300 Kgf (±20kgf)
    Per 20 'container 6144 pcs
    Per Pallet 256 pcs
    K-1
    • Strengths
    • Application
    • References
    • Accessories
    • Quality Certificates


    • 1- Fixing is done through the upper left nail hole in staggered floors. Thus, the nail hole is moved away from the direction of the water flow. The problem of water flowing from the nail hole is solved.
    • 2- In normal floorings, it can be fixed from the nail socket in the middle.
    • 3- Its smooth surface makes it difficult to hold dust and dirt.
    • 4- Duct movements of 2 cm in the vertical direction and 2.5 cm in the horizontal direction provide ease of application during installation.
    • 5- Its renewed structure is compatible with the existing old tiles in roof changes.






    • 1. The first lath (eave lath) and the two-lath spacing should be 30 cm from axle to axle, and the other lath spacing should be 33.6 cm. However, in order to be sure, it is necessary to determine the lath spacing on site after the tile lands on the construction site.
    • 2. The first lath should be 4 cm and other laths should be 2.2 or 2.5 cm high.
    • 3. The laying process should be from right to left when viewed from the front. The tooth on the right side of each tile should fit into the groove of the next tile.
    • 4. The threads of the next tile in the top row should also be placed in the grooves of the bottom row.
    • 5. Staggering the joints of the tiles in the upper row provides a more effective waterproofing. When installed with 20 ° - 30 ° inclinations, the first three rows of tiles on the eaves are completely nailed and in the following rows, if one is nailed in 3 rows, it is resistant to flying in 110km / hour wind.
    • 6. When tiles are laid on rafters roof covering (continuous covering such as wood or OSB), it is necessary to ventilate the bottom of the tiles. Deformation may occur on the lower surfaces of the tiles that are not ventilated due to condensation. In order to provide ventilation under the tiles, vertical lathing process is performed at 50 cm intervals on cold roofs, while channelled insulating plate should be used in hot roofs. In order to complete the circulation of the air under the tile, an insulation tape open to steam is used under the ridge.

    Ventilating Systems

    Ventilating Systems

    Universal Ventilating

    Universal Ventilating

    Aerial Entry

    Aerial Entry

    Aerial Entry

    Aerial Entry

    Eaves Tile

    Eaves Tile

    Left Eaves Tile

    Left Eaves Tile
    Technical Features
    Dimensions (cm) 16x18x41cm (±%2)
    Dimensions (inch) 6.29x7.08x16.14inch (±%2)
    Weight 3300gr (±100gr)

    Right Eaves Tile

    Right Eaves Tile
    Technical Features
    Dimensions (cm) 16x18x41cm (±%2)
    Dimensions (inch) 6.29x7.08x16.14 inch (±%2)
    Weigt 3300gr (±100gr)

    Ridge Starter

    Ridge Starter

    Ridge Starter

    Ridge Starter
    Technical Features
    Dimensions (cm) 19x38cm (±%2)
    Dimensions (inch) 7.48x14.96inch (±%2)
    Weight 3850gr (±100gr)
    Whatsapp Destek